CB 750 SOHC 1969-'77

All Prices are listed at the bottom of the page

The Honda CB 750 changed the face of motorcycling when it came out in the late sixties, and is a very popular bike to this day when it comes to cafe conversions. Plenty of power on tap - back when - classic lines and nice straight frame rails for easy mounting of tanks and seats.

We'll show you a nice selection of tanks, seats and quarter fairings and with some determination you will most likely be able to make some of the other stuff in our vintage section fit.

Don't forget to take a look at our clip-ons or clubman handlebars as well.

CR7501
Full fairing

What we have here is an exact replica of the kit fairing assembly that Honda offered for the CB750's. This classic one-piece race fairing assembly is extremely popular for vintage conversions. A tall fairing assembly works well with most street bike chassis; the open belly pan at the bottom allows you to adjust the width of the bottom. You can suck the fairing in real tight if you are installing on a 350 or 450 twin or spread it out wide if you are putting it on a 6 cylinder CBX. This is a very versatile and universal fairing assembly for a lot of applications. This is the classis café fairing that you need for your conversion.

Price

CR7501D
Oil Cooler Ducts

This is a "Works" part that was not available through the Honda CR kit part numbers. If you look at pictures closely enough at the '69 Daytona Bike (the orange one above) you'll see these two D shaped holes in the upper section of the fairing below the handlebars. Those holes were cut in the side of the fairing to evacuate the air out of the oil cooler, mounted onto the front forks. These duct assemblies were put behind the oil coolers and then sucked air out of the sides of the fairing to make the oil cooler more efficient. These are very rare, non-stock Honda pieces that are now made available to you. Call our sales reps and get a pair of them today!

Price

CB75021
Honda CB 750 1969-76 Cafe seat
This cool cafe bubble seat was developed especially for the CB 750 K chassis to work with the stock seat latches and seat lock. It has two options to mount the seat lock (to match the different positions on early and late models). You can flip the seat up just like your stock seat to get acces to the battery, tools etc. This is as close to a bolt-on operation as it gets!

Works with the stock tank.

Add the upholstery pan below for a cushy seat and you're ready to roll.

Please note: In it's infinite wisdom Honda flipped the hinges to the other side of the frame in 1977 and this seat will NOT work on those models. There may be some overlap in production runs so please check and make sure the stock seat flips up to the right on your bike - as shown in the picture here.

Price

CB75021M
Cafe seat
Modified version, excellent fit on DOHC Honda CB750, or on the SOHC if you want the seat directly on the frame rails.

Price

CB75021UP
Upholstery pan for CB75021 and CB75021M

Price

 

CB75022
Honda CB 750 F (long chassis) cafe seat
This is the 'Works' style seat that fits the longer F-chassis frame rails.

Works with the stock tank.

This seat is open in the back. Separate taillight insert available upon request for $40, see CB75022TLB below.

Add the upholstery pan below for a cushy seat and you're ready to roll.

Price

CB75022UP
Upholstery pan for CB75022

Price

CB75022TLB
Taillight bracket for CB75022.

This bracket is sold separately. Position it inside your tail section to your liking and bond it into place with 2-minute epoxy. Standard (vertical) position shown below but can be angled with some trimming.

Price

CR7502F
Race Tail

What we have here is a factory style of tail section that was only available on some Honda factory prepared race bikes in Europe and Australia. Slightly different bubble shape than the kit tail section or the works tail section. This is a pretty cool seat and will work on a lot of other motorcycles.

Price

CR7502K
Race Tail

This is an exact replica of the kit style race tail that was available through your Honda dealers when you converted your CB750 into a CR racer.

This very short seat works best with our long road racing style fuel tank. If you are using a stock CB gas tank this seat would put you too far forward so you would be right up against the fuel tank in an uncomfortable riding position.

Price

 

CR7502KUP
Upholstery Pan

What we have here is a fiberglass seat pan that fits our CR7502K kit race tail section. Simply mount your tail section onto your chassis, place our upholstery pan onto your tail section, and position for mounting boltholes. Drill a couple of mounting bolt holes and position epoxy the short small bolds onto your seat pan, then take this pan to your local auto upholstery place to have them upholster it for you. This is a must have if you want to finish off your CR replica race bike.

Price

CR7502W
Race Tail

This is the works style of tail section, and this tail section is the exact original style of tail section that was on the Dick Mann 1969 Daytona road race motorcycle. So if you’re building and exact Dick Mann replica this is the tail section that you need! Call one of our sales reps today!

Price

UBS
Universal cafe tail

This cool duck tail breathes 70s chic... It fits both the CB 750 K and F chassis. You need to clean up the frame rails underneath the seat by removing some brackets and latches. This seat can be made to work with the stock tank, but looks much better with the sculpted UBT cafe tank below!

Price

LAVS2
Laverda seat without hatch door.

As shown on the black bike.

Price

 

UBT
Universal cafe tank

This cool 70s style cafe tank has heavily sculpted lines and fits nicely onto the CB frame. The knee cutouts give you something to grab onto under hard braking and look cool, too. The tank comes with a standard 3/8" NPT bung in one of three locations (click here to see bottom of tank) fit a Pingel fuel valve.

Price

Please note! This gas tank is not recommended for street use, this is a fiberglass gas tank that will not dent.  In the event of a crash, the gas tank may rupture and spill fuel possibly catching your motorcycle on fire. This gas tank is recommended for racing purposes, with racing fuel only! Read more...

RTT2
Reed Titan cafe tank 2
This tank fits real nice on a CB750 as well, as shown here on a very nice Dutch CB750. There are larger pictures in the customer gallery!

Price

Please note! This gas tank is not recommended for street use, this is a fiberglass gas tank that will not dent.  In the event of a crash, the gas tank may rupture and spill fuel possibly catching your motorcycle on fire. This gas tank is recommended for racing purposes, with racing fuel only! Read more...

CR7503M
Fuel Tank Modified

This fuel tank is identical in exterior appearance to our CR7503 fuel tank; the only difference is that the bottom tunnel has been highly modified for use on other Honda chassis. The lower sump in the rear has been removed and a tunnel has been widened considerably to fit into other various press steel chassis. This tank will actually fit any SOHC four cylinder CB (CB 350, 400, 500, 550, 750 SOHC).

Price

Please note! This gas tank is not recommended for street use, this is a fiberglass gas tank that will not dent.  In the event of a crash, the gas tank may rupture and spill fuel possibly catching your motorcycle on fire. This gas tank is recommended for racing purposes, with racing fuel only! Read more...

CB750DTOT
CB750 racing oil tank

Really trick lightweight oil tank with integrated inner rear fender. You will need to trim the flange around the top of the tank to match the frame contour so it fits between the frame tubes.

Comes epoxy coated, with a billet oil cap, 1/4" vent fitting on top and 2x 3/8" fittings on bottom.

Please note: Requires custom oil lines. We recommend you cut the ends of the stock lines on the motor side and have them put into new hoses. On the tank end you will need AN to 3/8" NPT adapters.

Price

 

 

AJSM4K
Dunstall cafe racer quarter fairing - kit

Complete kit consisting of the following parts:
- fairing
- windscreen (smoke)
- fairing brackets (2)
- windscreen screws (black)

This convenient kit provides you with all the parts you need* to mount the fairing onto your bike, for a great price!

*Ask our sales reps for mounting tips, you will want to fabricate a simple mounting bracket, coming off the brake splitter or bottom fork clamp for additional support.

Please note: You may substitute the competition version of this fairing AJSM4C in this kit - part# AJSM4CK.

Price

AJSM4C
Dunstall cafe quarter fairing - competition

This is the race version of the Dunstall quarter fairing. Great quarter fairing for a vintage race or track bike.
Also a cool little fairing to use on a custom street bike with a custom headlight. Also available in kit form with hardware and windscreen, part# AJSM4CK.

Price

CR7504
Front Fender
This is the front blade that replaces the steel front fender. Honda engineers designed the front forks on your motorcycle to work with that heavy steel brace on the front. Do not run your front forks without the steel brace, severe wobbling will occur. Simply take your stock fender and drill the rivets out to remove the steel fender from the fork brace and the front and rear hoops and reattach this fender onto your steel hardware. This lightweight fiberglass piece actually takes a lot of weight off your front fork assembly and helps the suspension reaction and makes your bike handle better.

Price

CB7505
Inner rear fender
This is a replacement for the stock black plastic inner rear fender on the early K models. Our fiberglass fender will be lighter and easier to trim than the stock Honda fender, if you need to modify it for your project.

Price

CR7505
Bracket Kit

This is a quick bracket kit assembly where you can make up to mount the CR7501 fairing assembly onto a CB chassis. This bracket kit is not an exact replica of the CR brackets, but simply one that aids you in mounting a race fairing onto your CB chassis. Save yourself a lot of time, aggravation, and fabrication your own and get our brackets today.

Price

 

CR750 Replica

Want to build a replica of Dick Mann's Daytona winning CR750?

Click here to see the parts

CB750 Dirt track

Want to do something different with your CB750? How about building a dirt tracker? Better yet, slap some street tires and lights on it and make it a street tracker!

Click here to see the parts

CB750 Cafe Bagger

Old school hot rod cool... Dustbin fairing, cool small saddle bags and a cafe seat!

Click here to see the parts


Notice:

Please note these very important items!

  • We sell an unfinished unpainted product, it is your responsibility to sand, finish, and paint the parts you buy from us.
  • The parts we sell are un-drilled; it is your responsibility to drill all of the mounting holes and fit the parts onto your chassis.
  • All of our parts may or may not include the internal mounting tabs. Please consult with our sales representative if you have any questions about mounting things like headlights and dashes.
  • It is the purchasers' responsibility to mount all of the products they purchase onto their machine. If you need assistance mounting these products call our sales reps for advise.

Part #
Description
Retail
CB750 1969-'77 SOHC
CR7501
HONDA CR750 FAIRING
$276.64
CB75021
CB 750 CAFE SEAT (K CHASSIS)
$131.41
CB75021M
CB 750 CAFE SEAT (K CHASSIS) - MODIFIED
$131.41
CB75021UP
UPHOLSTERY PAN FOR CB75021
$37.00
CB75022
CB 750 'WORKS' RACE SEAT (F CHASSIS)
$131.41
CB75022UP
UPHOLSTERY PAN FOR CB75022
$37.00
CB75022TLB
TAILLIGHT BRACKET FOR CB75022
$40.00
CR7502K
HONDA CR750 TAIL SECTION- KIT SUPERBIKE
$131.41
CR7502KUP
HONDA CR750 SUPERBIKE-SEAT PAN
$37.00
CR7502F
HONDA CR750 TAIL SECTION-SUPERBIKE-FACTORY
$131.41
CR7502W
HONDA CR750 TAIL SECTION-SUPERBIKE-WORKS
$131.41
CR7502W
HONDA CR750 TAIL SECTION-SUPERBIKE-WORKS
$131.41
LAVS2 LAVERDA SEAT W/OUT HATCH DOOR $131.41
UBS UNIVERSAL BIMOTA SEAT $131.41
UBT
UNIVERSAL CAFE TANK
$604.87
RTT2
READ TITAN CAFE TANK
$493.22
CR7503M
HONDA CR750 CAFE TANK - MODIFIED NO SUMP
$493.22
CB750DTOT
HONDA CB750 RACING OIL TANK - SOHC
$493.59
AJSM4K
CAFE QUARTER FAIRING KIT
$189.95
CR7504
HONDA CR750 FENDER-FRONT
$61.95
CB7505
HONDA CB750 INNER REAR FENDER
$62.25
CR7505
HONDA CR750 TO CB CHASSIS FAIRING MOUNTING BRACKET KIT
$210.00

 

To order call 760-598-3366 NOW!

Looking for some Honda CBR fairings? A CB 750 cafe seat? Some RC 30 fairings? Take a look at our extensive collection. Airtech carries a full selection of street and track fairings for most bikes!