BM26
Buell RS1200 Sprocket cover
This is an Air-Tech design sprocket cover for the sportster motor Buells. This cover actually covers the contours of the can cover on the sportster motor and looks way cool. It looks a lot better than the stock Buell plastic crap. This piece is available in fiberglass and carbon fiber. Call our sales reps today!

Price

BRS124
Buell RS1200 Tail section
if you're lucky enough to have one of these RS1200's and are unfortunate enough to need a replacement, you are in luck because we still make the parts. This is the long tail section that was used with the flip up solo seat cowl. You're going to have to salvage your old hardware off of your old tail section for it because that stuff is no longer available. Drill the mounting holes, mount everything up, and go riding again.

Price

BRS125
Buell RS1200 License plate bracket
This is a license plate/ tail light bracket that mounts onto the inside of the long tail. It takes a little trimming and a little bit of epoxy work, but then you can mount it to the inside of your tail section.

Price

BRS126
Buell RS1200 Fuel tank
Modern pump gas tears up fuel tanks, especially those old fiberglass tanks like on your Buell. So if you've had gas sitting in your bike for all of these years, chances are that your tank is a goner. We put a factory ethanol resistant epoxy coating in our tanks, and have sold quite a few of these to people who are in the exact situation you're probably in. Need a replacement tank for your Buell? We've got what you need. Give us a call today!

Price

Please note!!!! This gas tank is not recommended for street use, this is a fiberglass gas tank that will not dent!!!!  It is possible that the gas tank will rupture and spill fuel possibly catching your motorcycle on fire if you happen to crash on the street. This lightweight racing gas tank is recommended for racing purposes only!!!!

BRS127
Buell RS1200 filler panel
Right side filler panel that goes between the tail section and fairing assembly.

Price

BRS128
Buell RS1200 filler panel
Left side filler panel that goes between the tail section and gas tank, and it mounts below the upholstery.

Price

BRS129
Buell RS1200 Front fender
This is an exact replica of the RS and RSS Buells. Simply drill the mounting holes, mount onto your bike and go for a ride! As you can see we sell this fender in fiberglass but it is also available in carbon fiber call your sales rep for a price in carbon today.

Price

BRS1210
Buell RS1200 Dash panel
The picture shows this dash mantle upside down, but this is actually the right part you need for your RS1200. Stock fiberglass pieces are brittle and break easily our lightweight fiberglass piece is a direct replacement. Simply drill the mounting holes, mount it onto your chassis, and go riding.

Price

BRS1211
Buell RS1200 Solo seat cowl
This the flip up cowl assembly that works with the long BRS124 tail section. This two-piece design that is molded together is an exact duplicate of the stock Buell tail section. You simply need to drill the mounting holes and install your hardware off of your old tail section on it, mount it onto your bike, and go for a ride.

Price

BRSS121C
Buell RS1200 Competition upper
Identical in exterior shape to the street upper fairing with the exception that the headlight holes and turn signal holes have been filled in for race purposes.

Price

BRSS121S
Buell RS1200 Street upper
This is a direct replacement part for the RSS1200. Simply drill the mounting holes, sand, paint, and install.

Price

BRSS122
Buell RS1200 Right side panel
This is the piece that mounts to the fairing below the gas tank. As you can see from the picture the oval air filter cover has been filled in because a lot of guys use it as an S & S tear drop air filter cover. This allows you to cut and trim to fit around whichever air filter cover you're using. Or cut it open, if you're using a stock one, for an accurate restoration.

Price

BRS123
Buell RS1200 Left side panel
This is the left side panel that mounts to the fairing and fits below the gas tank in front of the seat sides. To replace this piece simply drill the mounting holes, paint, and install.

Price